Cisco 200-401 - Managing Industrial Networks with Cisco Networking Exam
Page: 3 / 13
Total 64 questions
Question #11 (Topic: Topic 2)
Which prompt is used to configure parameters for the Ethernet ports of an industrial
switch?
switch?
A. Switch(config-if)#
B. Switch(config-if-ind)#
C. Switch(config-line)#
D. Switch(config-ind)#
E. Switch(config-vlan)#
Answer: A
Question #12 (Topic: Topic 2)
Exhibit:
[Cisco-200-401-7.0/Cisco-200-401-9_2.png]
Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the
VLANs. All the interfaces have been properly configured and IP routing is operational. The
hosts in the VLANs have been configured with the appropriate default gateway. What is
true about this configuration?
[Cisco-200-401-7.0/Cisco-200-401-9_2.png]
Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the
VLANs. All the interfaces have been properly configured and IP routing is operational. The
hosts in the VLANs have been configured with the appropriate default gateway. What is
true about this configuration?
A. These commands need to be added to the configuration:C-router(config)# router eigrp 123C-router(config-router)# network 172.19.0.0
B. These commands need to be added to the configuration:C-router(config)# router ospf 1C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
C. These commands need to be added to the configuration:C-router(config)# router ripC- router(config-router)# network 172.19.0.0
D. No further routing configuration is required.
Answer: D
Question #13 (Topic: Topic 2)
What are the two most relevant factors in determining the class of administration that is
required to maintain the telecommunications infrastructure? (Choose two.)
required to maintain the telecommunications infrastructure? (Choose two.)
A. the size of the infrastructure
B. the complexity of the infrastructure
C. the age of the infrastructure
D. the industry that the infrastructure supports
E. the physical environment of the infrastructure
Answer: A,B
Question #14 (Topic: Topic 2)
Exhibit:
[Cisco-200-401-7.0/Cisco-200-401-10_2.png]
Refer to the exhibit. CCNA.com has the industrial network shown in the exhibit. All switches
are configured as layer 2 switches and are using VLAN 1 as their management VLAN.
Each VLAN 1 interface has been assigned the correct IP address. What is the purpose of
assigning a default gateway to SW-C switch?
[Cisco-200-401-7.0/Cisco-200-401-10_2.png]
Refer to the exhibit. CCNA.com has the industrial network shown in the exhibit. All switches
are configured as layer 2 switches and are using VLAN 1 as their management VLAN.
Each VLAN 1 interface has been assigned the correct IP address. What is the purpose of
assigning a default gateway to SW-C switch?
A. allows connectivity between the VLAN 1 interface on SW-C and other devices in the network.
B. allows connectivity between Host A and other devices in the network.
C. allows connectivity between Host B and other devices in the network.
D. allows the switch to pass traffic between Host A and Host B
Answer: A
Question #15 (Topic: Topic 2)
An administrator has connected devices to an industrial switch and, for security reasons,
wants the dynamically learned MAC addresses from the address table added to the
running configuration. What must be done to accomplish this?
wants the dynamically learned MAC addresses from the address table added to the
running configuration. What must be done to accomplish this?
A. Enable port security and use the keyword sticky.
B. Set the switchport mode to trunk and save the running configuration.
C. Use the switchport protected command to have the MAC addresses added to the configuration.
D. Use the no switchport port-security command to allow MAC addresses to be added to the configuration.
Answer: A
