Cisco 200-401 - Managing Industrial Networks with Cisco Networking Exam
Page: 2 / 13
Total 64 questions
Question #6 (Topic: Topic 1)
Exhibit:
[Cisco-200-401-7.0/Cisco-200-401-6_2.png]
Refer to the exhibit. What are three traffic and interconnection requirements for the devices
in the exhibit? (Choose three.)
[Cisco-200-401-7.0/Cisco-200-401-6_2.png]
Refer to the exhibit. What are three traffic and interconnection requirements for the devices
in the exhibit? (Choose three.)
A. The EtherNet/IP drive connections are in a high-voltage area and need protection from electromagnetic noise, so shielded cable that is rated for 600 V is advised.
B. EtherNet/IP devices such as the controller, drive, VoIP phone, and IP camera should be in the same VLAN.
C. CIP traffic has the highest bandwidth requirement so it needs the highest QoS setting.
D. EtherNet/IP drive traffic has high sensitivity to random drops, latency, and jitter.
E. Real-time motion control and VoIP traffic can share the same VLAN with the proper QoS setting.
F. IEEE1588 and PTP are important for ensuring real-time synchronization.
Answer: A,D,F
Question #7 (Topic: Topic 1)
Which option allows an EtherNet/IP I/O device to be safely installed where it is subject to
water immersion?
water immersion?
A. The device is rated IP20 and the power wiring is installed securely to the terminal block.
B. The device is rated IP67 and a power cordset is used.
C. The device is rated IP67 and immersed to 10 m.
D. The device is rated IP20 and immersed to 10 m.
Answer: B
Question #8 (Topic: Topic 1)
Exhibit:
[Cisco-200-401-7.0/Cisco-200-401-7_2.png]
Refer to the exhibit. Host 3 on Network A is sending data to Host 8 on Network B. Which
address is the default gateway of Host 3?
A. the address of the switch interface that is connected to router interface Fa0/0
B. the address of the switch interface that is connected to router interface Fa0/1
C. the address of the host that is connected to Network A
D. the address of the host that is connected to Network B
E. the address of the router interface Fa0/0
F. the address of the router interface Fa0/1
[Cisco-200-401-7.0/Cisco-200-401-7_2.png]
Refer to the exhibit. Host 3 on Network A is sending data to Host 8 on Network B. Which
address is the default gateway of Host 3?
A. the address of the switch interface that is connected to router interface Fa0/0
B. the address of the switch interface that is connected to router interface Fa0/1
C. the address of the host that is connected to Network A
D. the address of the host that is connected to Network B
E. the address of the router interface Fa0/0
F. the address of the router interface Fa0/1
Answer: E
Topic 2, Install, Replace, and Remove an Industrial Device
Question #9 (Topic: Topic 2)
Which three of the following components must be elected before the Spanning Tree
Protocol can converge in a switched LAN? (Choose three.)
Protocol can converge in a switched LAN? (Choose three.)
A. designated ports
B. duplex operating mode
C. fast mode ports
D. root bridge
E. root ports
F. BDPU priority
Answer: A,D,E
Question #10 (Topic: Topic 2)
Exhibit:
[Cisco-200-401-7.0/Cisco-200-401-8_2.png]
Refer to the exhibit. An industrial ruggedized network device needs to be installed in the
place of the icon labeled Network Device to accommodate a leased line attachment to the
Internet. Which network device and interface configuration meets the minimum
requirements for this installation?
[Cisco-200-401-7.0/Cisco-200-401-8_2.png]
Refer to the exhibit. An industrial ruggedized network device needs to be installed in the
place of the icon labeled Network Device to accommodate a leased line attachment to the
Internet. Which network device and interface configuration meets the minimum
requirements for this installation?
A. a router with two Ethernet interfaces
B. a switch with two Ethernet interfaces
C. a router with one Ethernet and one serial interface
D. a switch with one Ethernet and one serial interface
E. a router with one Ethernet and one modem interface
Answer: C
