Netapp NS0-094 - NetApp Hardware Support Engineer Professional Exam
Page: 3 / 12
Total 60 questions
Question #11 (Topic: Exam A)
You have replaced the cluster backend switches on a 4-node NetApp ONTAP cluster with new switches. After the replacement, you realize that the system shows errors for the old switches that were removed:
You also notice that system switch ethernet show shows four switches, the two old switches and the two new switches.
What action will resolve the issue?
You also notice that system switch ethernet show shows four switches, the two old switches and the two new switches.
What action will resolve the issue?
A. Perform a reboot of the affected node using the storage failover takeover command.
B. Delete the old switches from the database using the system switch ethernet delete command.
C. Clear the health alert using the system health alert delete command.
D. Reconnect the old switches and download a support bundle using the system switch ethernet log collect command.
Answer: B
Question #12 (Topic: Exam A)
You receive the following AutoSupport message:
When researching, you discover the following output:
What action do you take to resolve this issue?
When researching, you discover the following output:
What action do you take to resolve this issue?
A. Replace the SFP on port e0a on node-02.
B. Update the RCF file on the cluster switches.
C. Update the firmware on the cluster switches.
D. Replace the SFP on port e0a on node-01.
Answer: A
Question #13 (Topic: Exam A)
While reviewing a fresh install of a new NetApp ONTAP HA pair, the Field Support engineer notices that the controllers do not report the same system storage configuration.
The first controller reports the following: System Storage Configuration: Multi-Path HA
The second controller reports the following: System Storage Configuration: Single-Path HA
There are no EMS errors, and there are no alerts on the system or on NetApp ONTAP System Manager.
What is the next step in troubleshooting this issue?
The first controller reports the following: System Storage Configuration: Multi-Path HA
The second controller reports the following: System Storage Configuration: Single-Path HA
There are no EMS errors, and there are no alerts on the system or on NetApp ONTAP System Manager.
What is the next step in troubleshooting this issue?
A. Ensure that the second controller is set up for ADP.
B. Ensure that all disk shelves are connected, with at least four SAS cables to each controller.
C. Reboot the controller that is reporting the single-path configuration.
D. Check cabling to the controller that is reporting the single-path configuration.
Answer: D
Question #14 (Topic: Exam A)
You notice the following system alert during a routine check of a four-node NetApp ONTAP cluster:
The customer confirms that the cables are connected correctly and interface LEDs on the switches are on.
What is the next step in troubleshooting this issue?
The customer confirms that the cables are connected correctly and interface LEDs on the switches are on.
What is the next step in troubleshooting this issue?
A. Remove the cluster ports from the cluster IPspace and cluster broadcast domain, and delete the health alerts.
B. Verify the configuration of the switchports with the output of RCF Configurator.
C. Bounce the cluster interconnect ports on the ONTAP cluster nodes that are reporting this alert.
D. Revert the ONTAP software upgrade to see if the alert disappears.
Answer: B
Question #15 (Topic: Exam A)
A storage administrator is troubleshooting a 4-node cluster, where one node is reporting “cluster port is down” alerts. The node has recently been recabled to new cluster switches. The cluster ping-cluster command shows communication failures between the affected node and its partners over the cluster network. All physical cables have been verified as properly seated and undamaged.
Which configuration is causing this problem?
Which configuration is causing this problem?
A. The MTU size on the new cluster switches is mismatched with the nodes.
B. An incorrect gateway is defined for the management network.
C. An incorrect intercluster LIF is configured.
D. The SVM data LIFs are on the wrong ports.
Answer: A
