Juniper JN0-692 - Service Provider Routing and Switching Support, Professional Exam
Page: 3 / 35
Total 171 questions
Question #11 (Topic: Topic 1)
Click the Exhibit button.
[Juniper-JN0-692-4.0/Juniper-JN0-692-9_2.png]
Your router should be configured with a rewrite rule which alters the default behavior of
expedited-forwarding as shown in the exhibit. Which configuration is correct?
[Juniper-JN0-692-4.0/Juniper-JN0-692-10_2.png]
[Juniper-JN0-692-4.0/Juniper-JN0-692-9_2.png]
Your router should be configured with a rewrite rule which alters the default behavior of
expedited-forwarding as shown in the exhibit. Which configuration is correct?
[Juniper-JN0-692-4.0/Juniper-JN0-692-10_2.png]
A. Option A
B. Option B
C. Option C
D. Option D
Answer: A
Question #12 (Topic: Topic 1)
You are facing BGP scaling issues and decide to add dedicated route reflectors to your
network. You notice that VPN routes are not being advertised by your route reflectors.
Which three actions can you take to solve this? (Choose three.)
network. You notice that VPN routes are not being advertised by your route reflectors.
Which three actions can you take to solve this? (Choose three.)
A. Add a static default route to inet.3 and/or inet6.3 on the route reflectors.
B. Add a full mesh of MPLS LSPs between all of the route reflectors.
C. Add MPLS LSPs between the route reflectors and their client routers.
D. Add a static default route to inet.3 and/or inet6.3 on all of the client routers.
E. Use rib-groups to add IGP routes to inet.3 and/or inet6.3 on the route reflectors.
Answer: A,C,E
Question #13 (Topic: Topic 1)
[Juniper-JN0-692-4.0/Juniper-JN0-692-11_2.png]
Referring to the exhibit, which statement is true about the multicast state on R3?
Referring to the exhibit, which statement is true about the multicast state on R3?
A. R3 has no PIM neighbors.
B. R3 has no receivers.
C. R3 has no route to RP.
D. R3 is not receiving any traffic
Answer: D
Question #14 (Topic: Topic 1)
[Juniper-JN0-692-4.0/Juniper-JN0-692-12_2.png]
You have been asked to troubleshoot an OSPF problem where the OSPF session will not
establish.
According to the outputs shown in the exhibit, which statement is true?
You have been asked to troubleshoot an OSPF problem where the OSPF session will not
establish.
According to the outputs shown in the exhibit, which statement is true?
A. The hold-time interval is set too low.
B. There is an MTU mismatch.
C. The hold-time interval is set too high.
D. The dead-interval is set too low.
Answer: B
Question #15 (Topic: Topic 1)
Click the Exhibit button.
[Juniper-JN0-692-4.0/Juniper-JN0-692-13_2.png]
The IGP is IS-IS. Routes from R1 need to be present on R6. Referring to the exhibit, what
will accomplish this task?
[Juniper-JN0-692-4.0/Juniper-JN0-692-13_2.png]
The IGP is IS-IS. Routes from R1 need to be present on R6. Referring to the exhibit, what
will accomplish this task?
A. Create an L1 adjacency between R2 and R3 to allow the routes to pass through to R6.
B. Use policy on R3 to leak R1's routes from L2 to L1.
C. Change the area address from 49.0003 to 49.0001 on R6 to allow R6 to accept routes from R1.
D. Use policy on R2 to leak R1's routes from L1 to L2.
Answer: B
