HP HPE0-Y53 - Building HPE SDN and FlexNetwork Solutions Exam
Page: 3 / 17
Total 84 questions
Question #11 (Topic: )
Evaluate each scenario for multi-tenant isolation, and match the scenario to the technology
that best meets its needs.
[HP-HPE0-Y53-8.0/HP-HPE0-Y53-7_2.png]
that best meets its needs.
[HP-HPE0-Y53-8.0/HP-HPE0-Y53-7_2.png]
Answer: [HP-HPE0-Y53-8.0/HP-HPE0-Y53-7_3.png]
Question #12 (Topic: )
A company has deployed the HP Network Protector SDN Application solution. The network
administrator wants to use this application to prevent clients from accessing specific
devices on the private network, including other clients. Which HP Network Protector feature
should the administrator use to configure this policy?
administrator wants to use this application to prevent clients from accessing specific
devices on the private network, including other clients. Which HP Network Protector feature
should the administrator use to configure this policy?
A. greylists
B. blacklists
C. Policies
D. ACL Manager
Answer: D
Question #13 (Topic: )
[HP-HPE0-Y53-8.0/HP-HPE0-Y53-8_2.png]
A network administrator sends the cURL command shown in the exhibit to an HP VAN
SDN Controller team in order to add a region to that team. The addresses are as follows:
The administrator receives an error in response. How can the administrator fix the
configuration?
A network administrator sends the cURL command shown in the exhibit to an HP VAN
SDN Controller team in order to add a region to that team. The addresses are as follows:
The administrator receives an error in response. How can the administrator fix the
configuration?
A. by configuring the region on the northbound team interface
B. by configuring the region before combining the controllers in a team
C. by specifying three controllers for the region rather than two
D. by assigning the devices' IP addresses in the same subnet as the controllers
Answer: C
Question #14 (Topic: )
Refer to Exhibit:
[HP-HPE0-Y53-8.0/HP-HPE0-Y53-9_2.png]
A standard ARP packet arrives on the switch with the flows shown in the exhibit. How does
the switch handle the packet? (Select two.)
[HP-HPE0-Y53-8.0/HP-HPE0-Y53-9_2.png]
A standard ARP packet arrives on the switch with the flows shown in the exhibit. How does
the switch handle the packet? (Select two.)
A. it encapsulates the packet and sends it to the controller.
B. ft forwards the packet normally.
C. it drops the packet.
D. It transmits the packet on port 200.
E. It transmits the packet on the ports in group table 200.
Answer: A,B
Question #15 (Topic: )
Refer to the exhibits on the Exhibit 1 and Exhibit 2 tabs.
[HP-HPE0-Y53-8.0/HP-HPE0-Y53-10_2.png]
Exhibit 2
[HP-HPE0-Y53-8.0/HP-HPE0-Y53-10_3.png]
Network clients are configured to use the switch as their default gateway in VLAN 2. The
HP Comware switch places VLAN 2 in OpenFlow instance 1. An SDN application has
created the flow entry shown in Exhibit 1 to route traffic from 10.1.2.0/24 to 10.1.3.0/24.
Exhibit 1 does not show the output interface for the flow.
Which output interface supports the needs of this scenario?
[HP-HPE0-Y53-8.0/HP-HPE0-Y53-10_2.png]
Exhibit 2
[HP-HPE0-Y53-8.0/HP-HPE0-Y53-10_3.png]
Network clients are configured to use the switch as their default gateway in VLAN 2. The
HP Comware switch places VLAN 2 in OpenFlow instance 1. An SDN application has
created the flow entry shown in Exhibit 1 to route traffic from 10.1.2.0/24 to 10.1.3.0/24.
Exhibit 1 does not show the output interface for the flow.
Which output interface supports the needs of this scenario?
A. controller
B. ANY
C. NORMAL
D. TABLE
Answer: C
