Cisco 300-370 - Troubleshooting Cisco Wireless Enterprise Networks Exam
Page: 3 / 12
Total 60 questions
Question #11 (Topic: )
Two 5508 Wireless Lan Controllers are managing all Access Points throughout the network
The WLCs are located in different locations to provide geographical redundancy A Mobility
Group has been configured on both WLCs and has a UP status on both Controllers The
APs m location A are statically configured to use Controller A as the Primary and Controller
B as the Secondary If the WLC in location A goes offline, the APs successfully join the
WLC m location B but they do not failover to their Primary configured Controller What
configuration task will fix this issue'
The WLCs are located in different locations to provide geographical redundancy A Mobility
Group has been configured on both WLCs and has a UP status on both Controllers The
APs m location A are statically configured to use Controller A as the Primary and Controller
B as the Secondary If the WLC in location A goes offline, the APs successfully join the
WLC m location B but they do not failover to their Primary configured Controller What
configuration task will fix this issue'
A. Change the AP Failover Priority to critical.
B. Enable AP Fallback globally on the WLC.
C. Configure the WLC in location A as Primary using the CAPWAP AP Controller IP Address command on all the location A Access Points.
D. Use DHCP Option 43 and specify WLC in location A as Primary.
Answer: C
Question #12 (Topic: )
Which statement describes how the Hand Select feature works on the wireless controller?
Refer to the exhibit.
[Cisco-300-370-7.0/Cisco-300-370-6_2.png]
Refer to the exhibit.
[Cisco-300-370-7.0/Cisco-300-370-6_2.png]
A. The access point uses the load balancing feature to move the clients to 5 Ghz.
B. The access point changes the DTIM period on the 2 4 Ghz band.
C. The access point recommends the band in the association response to the client.
D. The access point ignores and delays the probe request of the client on the 2 4 Ghz.
Answer: C
Question #13 (Topic: )
A Wireless LAN Cisco engineer is troubleshooting 802. 11ac WLAN at customer site Doe
to interferences with neighboring 802 11n networks the engineer must determine the
current primary secondary channel allocation to enhance the current configuration.
Channel 60 has been chosen by the customer as primary 20 MHz channel. Which
combination determines the resulting primary 40 MHz and primary 80 MHZ channels?
to interferences with neighboring 802 11n networks the engineer must determine the
current primary secondary channel allocation to enhance the current configuration.
Channel 60 has been chosen by the customer as primary 20 MHz channel. Which
combination determines the resulting primary 40 MHz and primary 80 MHZ channels?
A. primary 40 MHz channel 62, primary 80 MM: channel 58
B. primary 40 MHz channel 54, primary 80 MHz channel 58
C. primary 40 MHz channel 64, primary 80 MHz channel 60
D. primary 40 MHz channel 60, primary 80 MHz channel 56
Answer: A
Question #14 (Topic: )
A WLAN engineer has just completed a wireless network installation using Cisco 2700
series access points. After checking the WLC, it seems that the APs are running in medium
power. What effect will this have in the APs?
series access points. After checking the WLC, it seems that the APs are running in medium
power. What effect will this have in the APs?
A. Due to insufficient power, the access points are not broadcasting any Wireless networks.
B. Due to insufficient power, only the 2 4 GHz radio is up.
C. Due to insufficient power the access points have dynamically shifted from 3x4 to 3x3.
D. Due to insufficient power the access points have dynamically shifted from 4x4 to 3x3.
Answer: C
Question #15 (Topic: )
An engineer is troubleshooting non-802 11 interference and observes this output. Which
type of interference signatures can be identified?
Refer to the exhibit.
[Cisco-300-370-7.0/Cisco-300-370-7_2.png]
type of interference signatures can be identified?
Refer to the exhibit.
[Cisco-300-370-7.0/Cisco-300-370-7_2.png]
A. one frequency hopping Bluetooth
B. two healthy CCK and one malformed OFDM
C. three broadband jammers
D. two strong microwave ovens and one moderate
Answer: B
