Citrix 1Y0-350 - Citrix NetScaler 10 Essentials and Networking Exam
Page: 3 / 26
Total 126 questions
Question #11 (Topic: )
Scenario: For security reasons, the NSIP needs to be configured to only be accessible on
interface 0/1, which is VLAN 300.
The NSIP address is 10.110.4.254 and the subnet mask is 255.255.255.0.
How would the network engineer achieve this configuration?
interface 0/1, which is VLAN 300.
The NSIP address is 10.110.4.254 and the subnet mask is 255.255.255.0.
How would the network engineer achieve this configuration?
A. set ns config -nsvlan 300 -ifnum 0/1
B. set ns ip 10.110.4.254 -gui ENABLED -vrID 300
C. add vlan 300 set ns ip 10.110.4.254 -mgmtAccess ENABLED
D. set ns config -IPAddress 10.110.4.254 -netmask 255.255.255.0
Answer: A
Question #12 (Topic: )
Why would an engineer want to specify a TCP Profile for a specific service group?
A. To enable use of features like SSL over TCP for that specific service group.
B. To adjust the TCP settings for traffic to and from that specific service group.
C. To use a specific SNIP for traffic to the back-end servers in that service group.
D. To enable features like use source IP, TCP keep alive and TCP buffering for a specific service group.
Answer: B
Question #13 (Topic: )
A network engineer wants to optimize a published load balanced SSL virtual server for
WAN connection with long delay, high bandwidth with minimal packet drops.
What would the network engineer use to do this type of optimization for the SSL virtual
server?
WAN connection with long delay, high bandwidth with minimal packet drops.
What would the network engineer use to do this type of optimization for the SSL virtual
server?
A. SSL policy
B. TCP profile
C. Compression policy
D. Priority queuing policy
Answer: B
Question #14 (Topic: )
Scenario: The NetScaler is connected to two subnets. The NSIP is 10.2.9.12. The external
SNIP is 10.2.7.3. The MIP for internal access is 10.2.9.3. Web servers, authentication
servers and time servers are on the 10.2.10.0/24 network which is available through the
10.2.9.1 router. The external firewall has the 10.2.7.1 address. Traffic bound for Internet
clients should flow through the external firewall.
Which command should be used to set the default route?
SNIP is 10.2.7.3. The MIP for internal access is 10.2.9.3. Web servers, authentication
servers and time servers are on the 10.2.10.0/24 network which is available through the
10.2.9.1 router. The external firewall has the 10.2.7.1 address. Traffic bound for Internet
clients should flow through the external firewall.
Which command should be used to set the default route?
A. add route 0.0.0.0 0.0.0.0 10.2.7.1
B. add route 0.0.0.0 0.0.0.0 10.2.9.1
C. add route 10.0.0.0 255.0.0.0 10.2.9.1
D. add route 10.0.0.0 255.0.0.0 10.2.7.1
Answer: A
Question #15 (Topic: )
Some SSL certificate files may be missing from a NetScaler appliance.
Which directory should an engineer check to determine which files are missing?
Which directory should an engineer check to determine which files are missing?
A. /nsconfig/ssl
B. /nsconfig/ssh
C. flash/nsconfig/
D. /var/netscaler/ssl/
Answer: A
