Fortinet NSE4_FGT-7.2 - Fortinet NSE 4 - FortiOS 7.2 Exam
Page: 3 / 21
Total 104 questions
Question #11 (Topic: Exam A)
Which two settings are required for SSL VPN to function between two FortiGate devices? (Choose two.)
A. The client FortiGate requires a manually added route to remote subnets.
B. The client FortiGate requires a client certificate signed by the CA on the server FortiGate.
C. The server FortiGate requires a CA certificate to verify the client FortiGate certificate.
D. The client FortiGate requires the SSL VPN tunnel interface type to connect SSL VPN.
Answer: BC
Question #12 (Topic: Exam A)
Which statement correctly describes the use of reliable logging on FortiGate?
A. Reliable logging is enabled by default in all configuration scenarios.
B. Reliable logging is required to encrypt the transmission of logs.
C. Reliable logging can be configured only using the CLI.
D. Reliable logging prevents the loss of logs when the local disk is full.
Answer: D
Question #13 (Topic: Exam A)
Refer to the exhibits.
The exhibits contain a network diagram, and virtual IP, IP pool, and firewall policies configuration information.
The WAN (port1) interface has the IP address 10.200.1.1/24.
The LAN (port3) interface has the IP address 10.0.1.254/24.
The first firewall policy has NAT enabled using IP pool.
The second firewall policy is configured with a VIP as the destination address.
Which IP address will be used to source NAT (SNAT) the internet traffic coming from a workstation with the IP address 10.0.1.10?
The exhibits contain a network diagram, and virtual IP, IP pool, and firewall policies configuration information.
The WAN (port1) interface has the IP address 10.200.1.1/24.
The LAN (port3) interface has the IP address 10.0.1.254/24.
The first firewall policy has NAT enabled using IP pool.
The second firewall policy is configured with a VIP as the destination address.
Which IP address will be used to source NAT (SNAT) the internet traffic coming from a workstation with the IP address 10.0.1.10?
A. 10.200.1.1
B. 10.0.1.254
C. 10.200.1.10
D. 10.200.1.100
Answer: D
Question #14 (Topic: Exam A)
Refer to the exhibit.
The exhibit shows a diagram of a FortiGate device connected to the network, the firewall policy and VIP configuration on the FortiGate device, and the routing table on the ISP router.
When the administrator tries to access the web server public address (203.0.113.2) from the internet, the connection times out. At the same time, the administrator runs a sniffer on FortiGate to capture incoming web traffic to the server and does not see any output.
Based on the information shown in the exhibit, what configuration change must the administrator make to fix the connectivity issue?
The exhibit shows a diagram of a FortiGate device connected to the network, the firewall policy and VIP configuration on the FortiGate device, and the routing table on the ISP router.
When the administrator tries to access the web server public address (203.0.113.2) from the internet, the connection times out. At the same time, the administrator runs a sniffer on FortiGate to capture incoming web traffic to the server and does not see any output.
Based on the information shown in the exhibit, what configuration change must the administrator make to fix the connectivity issue?
A. Configure a loopback interface with address 203.0.113.2/32.
B. In the VIP configuration, enable arp-reply.
C. Enable port forwarding on the server to map the external service port to the internal service port.
D. In the firewall policy configuration, enable match-vip.
Answer: D
Question #15 (Topic: Exam A)
Which two statements are true about the FGCP protocol? (Choose two.)
A. FGCP elects the primary FortiGate device.
B. FGCP is not used when FortiGate is in transparent mode.
C. FGCP runs only over the heartbeat links.
D. FGCP is used to discover FortiGate devices in different HA groups.
Answer: AD
