HP HPE7-A07 - HPE Campus Access Mobility Expert Exam
Page: 3 / 13
Total 62 questions
Question #11 (Topic: Exam A)
The ACME company has an AOS-CX 6200 VSF switch stack with an uplink over subscription ratio of 9.6.1 They have indicated that their low-priority TCP traffic has been flagged with a DSCP marking coloring them yellow.
Refer to the exhibit.
They are considering adding two more nodes to the stack without adding any additional uplinks due to existing wiring constraints One of their architects has suggested adding the following configuration:
What would be the impact of applying the acmethreshold profile as shown? (Choose two.)
Refer to the exhibit.
They are considering adding two more nodes to the stack without adding any additional uplinks due to existing wiring constraints One of their architects has suggested adding the following configuration:
What would be the impact of applying the acmethreshold profile as shown? (Choose two.)
A. All upper-layer protocol traffic egressing LAG1 will be subject to drop probability
B. All TCP traffic egressing LAG1 will be subject to drop probability
C. VoIP packets egressing any queue on LAG1 will more likely be protected from uplink over-utilization
D. Yellow-flagged TCP traffic egressing LAG1 will be subject to drop probability
E. Only VoIP packets egressing queue 5 on LAG1 will likely be protected from uplink over-utilization
Answer: CD
Question #12 (Topic: Exam A)
You configured a WPA3-SAE with the following MAC Authentication Role Mapping in HPE Aruba Networking Central Cloud Authentication and Policy:
With further default settings, assume a new Android phone is connected to the network. Which role will the client be assigned after connecting for the first time?
With further default settings, assume a new Android phone is connected to the network. Which role will the client be assigned after connecting for the first time?
A. iot-local
B. client will be rejected network access
C. byod
D. unmatched-device
Answer: C
Question #13 (Topic: Exam A)
Refer to the exhibits.
An engineer has applied the above configuration to R1 and R2. However, the router's OSPF adjacency never progresses past the "EXSTART/DR" state as shown below.
Which configuration action on either router will allow R1 and R2 to progress past the "EXSTART/DR" state?
An engineer has applied the above configuration to R1 and R2. However, the router's OSPF adjacency never progresses past the "EXSTART/DR" state as shown below.
Which configuration action on either router will allow R1 and R2 to progress past the "EXSTART/DR" state?
A. Remove the layer 3 MTU configuration.
B. Ensure the OSPF process is not configured with passive-interface default
C. Change the IP address and mask applied to interface 1/1/1
D. Change R1 and R2 to a network type of point-to-point.
Answer: D
Question #14 (Topic: Exam A)
A customer is evaluating device profiles on a CX 6300 switch. The test device has the following attribute:
MAC address = 81 :cd:93:13:ab:31
The test device needs to be assigned the “iot-prod” role. In addition, the “iot-default” role must be applied for any other device connected to interface 1/1/1.
This is a lab environment with no configuration of any external authentication server for the test.
Given the configuration example, what is required to meet this testing requirement?
MAC address = 81 :cd:93:13:ab:31
The test device needs to be assigned the “iot-prod” role. In addition, the “iot-default” role must be applied for any other device connected to interface 1/1/1.
This is a lab environment with no configuration of any external authentication server for the test.
Given the configuration example, what is required to meet this testing requirement?
A. Enter the command "port-access device-profile mode block-until-profile-applied" for interface 1/1/1.
B. Enter the command "port-access fallback-role lot-default" for interface 1/1/1
C. Enter the command "port-access onboarding-method precedence" to set device profiles with a higher precedence.
D. Enter the command "port-access onboarding-method precedence" to set device profiles with a lower precedence.
Answer: B
Question #15 (Topic: Exam A)
Refer to the exhibits.
A network administrator attempts to improve multicast traffic flow and performs some packet captures for validation. What can the network administrator conclude from the results?
A network administrator attempts to improve multicast traffic flow and performs some packet captures for validation. What can the network administrator conclude from the results?
A. The data rate increased from 6 Mbps to 300 Mbps because Broadcast Multicast Optimization (BCMCO) was configured.
B. The data rate increased from 6 Mbps to 300 Mbps because Dynamic Multicast Optimization (DMO) was configured.
C. The capture taken after optimization does not show a packet length because Multicast Transmission Optimization was configured.
Answer: B
