Page: 1
/ 5
Total 66 questions
A company is using XtremIO for their RecoverPoint environment. They have approximately 100 GB of cumulative changes per day with the change being constant throughout the day. The company has a requirement to roll back 48 hours.
How should the Journals be sized and how should the copy policy be configured to ensure maximum protection with the least amount of storage used?
- A. 5 GB with the "Required Protection Window" set for 2 days
- B. 10 GB with the "Required Protection Window" set for 2 days
- C. 40 GB with the "Required Protection Window" set for 2 days
- D. 200 GB with the "Required Protection Window" set for Default
Answer : C
A RecoverPoint administrator is using the CLI to create a new Consistency Group. After beginning the process by running the command create_group, what is the next command that needs to be run?
- A. add-replication_volume
- B. create_replication_volume
- C. create_production_copy
- D. add_group_set
Answer : B
A RecoverPoint system has been deployed with XtremIO at production and disaster recovery sites. What is an accurate statement, if the replication mode for a
Consistency Group has been set as "Continuous"?
- A. Effective RPO will be 0 seconds
- B. Set customized time between cycles
- C. Effective RPO can be <60 seconds
- D. Set minimum time between cycles
Answer : D
A RecoverPoint storage administrator needs to protect a mission critical application. The application is stored on three volumes provisioned from a new VNX.
Once the Consistency Group is created for the application, how many replication sets will the group contain?
- A. 1
- B. 2
- C. 3
- D. Determined by the number of copies
Answer : C
A storage administrator is creating a Consistency Group using Unisphere on RecoverPoint/EX. After defining the production volume and Journal, the next step is to select the copy volume. Based on the exhibit, what determines the volume size displayed by the wizard as a choice of copy volumes?
- A. Volumes that are created on the selected array and masked to the backup host
- B. Volumes that are the same size and attached to the selected write splitter
- C. Volumes that are masked to the selected cluster and the same size or larger than production
- D. Any volume that is provisioned to the selected cluster from the same array type as production
Answer : D
What is the purpose of the save_settings command?
- A. Create a script file that can later be used to recreate the system configuration
- B. Modify or configure the RecoverPoint configuration backup interval
- C. Preserve the configuration of a RecoverPoint Appliance prior to replacement
- D. Commit cluster configuration changes to the repository volume
Answer : A
Reference:
https://community.emc.com/thread/124306?tstart=0
Which EMC product integrates with RecoverPoint to provide application-driven point-in-time copies?
- A. ProtectPoint
- B. ViPR SRM
- C. Data Domain
- D. AppSync
Answer : C
A storage administrator is unable to perform Direct Access to a copy in their RecoverPoint environment. Which array type has this limitation with regards to
RecoverPoint copies?
- A. XtremIO
- B. VMAX
- C. VNX
- D. VPLEX
Answer : A
When using a Distributed Consistency Group, additional traffic is generated between the primary RPA and secondary RPAs. Where is this increase in traffic observed?
- A. Additional traffic is seen on the WAN network between the RPAs
- B. Additional traffic is seen on the FC links between the RPAs
- C. No additional traffic will be observed because host writes are multicast to all appliances in a cluster
- D. Additional traffic is seen on the management network between the RPAs
Answer : D
What describes RecoverPoint asynchronous replication write operations to the Journal volumes?
- A. Journal is written to at three times the rate of the production volumes
- B. Volumes of the same capacities will be concatenated and not striped
- C. Writes to the Journal volume are typically small sequential writes
- D. Writes to the Journal volume are typically large sequential writes
Answer : D
Which command can be used to reduce the impact of the initial volume synchronization on production applications?
- A. config_io_throttling throttling=high
- B. config_link_policy group= cgname copy_1=prod_copy copy_2= dr_copy regulate_application=yes
- C. config_link_policy group= cgname copy_1=prod_copy copy_2= dr_copy regulate_application=no
- D. config_io_throttling throttling=none
Answer : B
After creating a Consistency Group with a local copy, initialization is taking longer than expected. What is a possible reason for this condition?
- A. Limited WAN bandwidth is available to the RPAs
- B. Slow performing storage on the production array
- C. Copy is not attached to the same splitter as production
- D. Size mismatch between the production and the copy volumes
Answer : B
A storage administrator is selecting Test a Copy to enable an Image Access for an XtremIO-to-XtremIO Consistency Group. Why is Logged Access the only allowable access mode with this type of replication?
- A. Direct Access is not possible because the copy cannot be mounted on XtremIO
- B. XtremIO cannot process the changes to the Journal required for Virtual Access
- C. XtremIO snapshots are not host accessible when using RecoverPoint
- D. XtremIO uses snapshots which are instantly promoted as the SCSI personality of the copy
Answer : D
A RecoverPoint administrator performs a Consistency Group failover to a remote copy. What happens to the point-in-time images stored in the copy Journal after the copy becomes production?
- A. Images are consolidated
- B. Images are deleted
- C. Images are replicated to the new copy Journal
- D. Images are replicated to the new production Journal
Answer : C
An administrator wants to integrate Site Recovery Manager (SRM) with RecoverPoint. Where should the RecoverPoint storage replication adapter be installed?
- A. On the same servers running VCenter and the SRM service
- B. On servers running SRM service only
- C. On servers running VCenter only
- D. On a newly installed server
Answer : B
Reference:
https://cpsdocs.dellemc.com/bundle/P_DP_PG/page/GUID-0931137B-AA03-4CC0-9766-2F184DC21947.html
30 days access 