Conducting Cisco Unified Wireless Site Survey V2 v10.0 (642-732)

Page:    1 / 13   
Total 196 questions

An engineer is deploying centralized wireless solution with a 5508 controller. What is the most AP licenses that can be supported?

  • A. 50
  • B. 100
  • C. 250
  • D. 500
  • E. 1000


Answer : D

Refer to the exhibit.


What is the most likely cause of MAP1 association to MAP2 instead of directly to the RAP?

  • A. Incorrect BGN
  • B. Default BGN
  • C. SNR
  • D. Absorption and scattering caused by weather conditions.
  • E. Incorrect radio configuration


Answer : C

An engineer is tasked with designing a WLAN. The customer is prioritizing data speeds to the desktop, but is also entertaining the idea of adding 802.11 phones in the future. Given this information, how should the engineer conduct the survey?

  • A. consider the employee head count in congested office space and limit the edge of each cell to an RSSI of -67mW
  • B. restrict AP cell edges to -67dB and be sure to strategically place APs in congested office spaces
  • C. co-locate access points when possible to cover high user areas and place APs at each corner of the facility
  • D. stagger the AP placements, and be sure to have a high signal to noise ratio that will accommodate the future VoIP devices


Answer : B

When designing and deploying an outdoor mesh network, what is the appropriate RF cell overlap?

  • A. 10 percent
  • B. 15 percent
  • C. 20 percent
  • D. 25 percent
  • E. Application dependent


Answer : E

An engineer wants to provide coverage between warehouse shelving stocked with bulk metal materials. What antenna would be adequate for performing this survey?

  • A. 5.5 dBi omni down tilt
  • B. 17 dBi grid
  • C. 2.2 dBi omni
  • D. 8.5 dBi patch


Answer : D

A wireless engineer is gathering equipment to perform a point-to-point bridge survey. What three pieces of equipment should be used? (Choose three.)

  • A. 3502i with dual band directional antennas
  • B. 3502e with AIR-ANT2460NP-R
  • C. 1132 with a 10dBi Yagi
  • D. 1552e with three AIR-ANT2547-N=
  • E. 1552e with AIR-ANT2588P3M-N=
  • F. 1310 with internal antenna
  • G. 1142 Series with internal antennas


Answer : B,E,F

Which option will allow the maximum 2.4 GHz channel usage for a survey and voice deployment in the ETSI domain?

  • A. 1, 6, 11
  • B. 1, 5, 9, 13
  • C. 1, 6, 9, 14
  • D. 1, 6, 11, 14


Answer : A

Which two types of information should be included in the installation inventory portion of the post-installation report? (Choose two.)

  • A. All AP, controller, and MSE administrator credentials
  • B. The number and type of all WLAN clients and tags
  • C. The names, locations, IP addresses, MAC addresses, etc. for every AP, controller, and MSE in the WLAN
  • D. Results of the coverage audit performed with the site survey mapping tool


Answer : A,C

Which two details are specified in the Executive Summary section of the Site Survey
Report? (Choose two.)

  • A. proposed location for each AP
  • B. customer and site surveyor contact details
  • C. total number of APs
  • D. expressed requirements set by customer
  • E. coverage map


Answer : C,D

How many location points are needed to validate both 802.11b/g and 802.11a in the Cisco
WCS Calibration?

  • A. 50
  • B. 100
  • C. 150
  • D. 200
  • E. 300


Answer : E

What is the optimal distance between APs for location services without taking into consideration the physical environment?

  • A. 90 to 120 feet
  • B. 80 to 100 feet
  • C. 40 to 70 feet
  • D. 10 to 25 feet
  • E. 5 to 20 feet


Answer : C

A company has requested an indoor wireless survey that supports 5GHz radio, 3x4 MIMO technology, and 3 spatial streams. Which AP is used to perform this survey?

  • A. 600
  • B. 1242
  • C. 1600
  • D. 2600
  • E. 3600


Answer : D

A small medical office would like to have wireless ability. Which survey tool would provide the fastest AP locations without sacrificing quality?

  • A. Air Magnet predictive survey tool
  • B. Cisco Spectrum Analyzer tool
  • C. Cisco Spectrum Expert utility
  • D. Air Magnet Survey Pro-active survey


Answer : A

Which two issues can commonly create problems with positioning an antenna on a rooftop? (Choose two.)

  • A. Reflection from the rooftop
  • B. Absorption from the rooftop
  • C. Fresnel obstruction from rooftop edge
  • D. Lack of PoE for AP
  • E. Other antennas


Answer : C,E

After installation of a new data-only wireless network, an engineer found that RRM has set all of the APs to a power level of 1. Which option describes the reason for this?

  • A. APs are too far apart for the set data rates.
  • B. EDRRM is enabled.
  • C. APs should be manually set initially.
  • D. TPC needs to be enabled.
  • E. DTPC value is set too high.
  • F. High co-channel interference exists.


Answer : A

Page:    1 / 13   
Total 196 questions