VMware vSAN Specialist v2 v1.0 (5V0-22.23)

Page:    1 / 5   
Total 75 questions

Which vSAN maintenance mode option should be used to avoid storage policy non-compliance?

  • A. Ensure accessibility
  • B. Partial maintenance mode
  • C. Full data migration
  • D. No data migration


Answer : C

vSAN requires that the virtual machines deployed on the vSAN datastores are assigned at least one storage policy, but the administrator did not explicitly assign a storage policy when provisioning the new VM.
What is the result of this situation?

  • A. The VM provisioning will fail.
  • B. The VM objects will be protected based on the vSAN Default Storage Policy configurations.
  • C. The vSphere Web Client will choose the last vSAN Storage Policy used.
  • D. No data protection will be applied to the VM objects.


Answer : B

An administrator is upgrading multiple vSAN Witness nodes with vLCM (single image management) that are used for vSAN Stretched and two-node Clusters.
What two witness node types can the administrator upgrade? (Choose two.)

  • A. Appliance witness node
  • B. Shared witness node
  • C. Nested witness node
  • D. Dedicated witness node
  • E. Physical witness node


Answer : AE

A vSAN administrator notices that the VMware Skyline Health: Network Latency Check reports indicate that three hosts are noncompliant.
Which action should the vSAN administrator take?

  • A. Immediately reboot the non-compliant hosts
  • B. Check VMKNICs, uplinks, physical switches, and associated settings
  • C. Rerun the VMware Skyline Health: vSAN Cluster Partition report
  • D. Place the non-compliant hosts into an isolated network partition


Answer : B

A vSAN administrator needs to enable vSAN ESA.
Which two requirements need to be met? (Choose two.)

  • A. vSAN Build Your Own configuration
  • B. vSAN Standard license
  • C. vSAN Witness Appliance
  • D. vSAN Advanced license
  • E. vSAN ReadyNodes configuration


Answer : AE

What are two prerequisites for using the TRIM and UNMAP capability of vSAN? (Choose two.)

  • A. Deduplication and compression are enabled.
  • B. The vSAN cluster is an all-flash architecture.
  • C. The VM guest operating system supports ATA TRIM or SCSI UNMAP capability.
  • D. TRIM and UNMAP is enabled.
  • E. Change the Object Space Reservation to 100.


Answer : BC

How often does the Skyline Health interval validate online if there are new Health Checks available for vSAN?

  • A. Every 1 hour
  • B. Every 4 hours
  • C. Every 24 hours
  • D. Every 12 hours


Answer : C

A vSAN administrator is tasked to perform an upgrade of a vSAN cluster, including firmware and drivers for its hardware. The vSAN administrator already created an image using vSphere Lifecycle Manager (vLCM).
Prior to selecting Start Remediation, which step should be taken to upgrade the complete vSAN cluster as a single task?

  • A. Select Remediate All through vLCM to upgrade all hosts in the cluster
  • B. Place all hosts in the vSAN cluster into Maintenance Mode
  • C. Stage the upgrade of the vSAN cluster through vLCM
  • D. Manually remediate one host at a time in the vSAN cluster


Answer : A

After reviewing various performance charts at a cluster level, an administrator found an individual VM impacting overall performance of the vSAN cluster.
What feature should be used to introspect multiple performance metrics of a single virtual machine?

  • A. esxcli
  • B. Skyline Health
  • C. I/O Trip Analyzer
  • D. IOInsight


Answer : D

An existing vSAN OSA cluster has this specification:
Four ESXi hosts with all flash configuration

Each with two disk groups -
Each disk group with one cache device and four capacity devices
There are five more device slots available per host
The CTO would like to provision new applications, and these will need more capacity and performance.
Which two methods should be used by the vSAN administrator to meet this goal with the least amount of impact? (Choose two.)

  • A. Replacing all capacity devices with a similar larger device
  • B. Replacing all cache devices with a larger device
  • C. Adding one more disk group per host with the same configuration
  • D. Adding faster cache devices
  • E. Adding an ESXi host with identical device configuration


Answer : CE

A customer has deployed a new vSAN cluster with the following configuration:
5 x vSAN ReadyNodes

All Flash -
12 TB Raw Storage
vSAN 8 is deployed with ESA.
New VMs are configured with a RAID-5 VM policy.
Which statement is accurate?

  • A. vSAN will use a 2+1 RAID-5 data placement scheme with parity will be used
  • B. RAID 5 will provide an FTT=2 level of protection in this case
  • C. vSAN will use a 4+1 RAID-5 data placement scheme with parity will be used
  • D. vSAN will spread the components across all of the disk groups


Answer : D

After a planned power outage, an administrator decided to restart the vSAN cluster manually.
What is the correct sequence of steps for the administrator to follow after powering on the ESXi hosts?

  • A. 1. Enable cluster member updates from vCenter Server only on one ESXi host.
    2. Run the python reboot helper script only on one ESXi host to recover the cluster.
    3. Exit all hosts from maintenance mode.
  • B. 1. Exit all hosts from maintenance mode.
    2. Run the python reboot helper script only on one ESXi host to recover the cluster.
    3. Enable cluster member updates from vCenter Server on all ESXi hosts.
  • C. 1. Exit all hosts from maintenance mode.
    2. Enable cluster member updates from vCenter Server only on one ESXi host.
    3. Run the python reboot helper script only on one ESXi host to recover the cluster.
  • D. 1. Enable cluster member updates from vCenter Server on all ESXi hosts.
    2. Run the python reboot helper script on all ESXi hosts to recover the cluster.
    3. Exit all hosts from maintenance mode.


Answer : A

After a server power failure, the administrator noticed the scheduled resyncing in the cluster monitor displays objects to be resynchronized under the pending category.
Why are there objects in this category?

  • A. The delay timer has not expired.
  • B. These objects belong to virtual machines, which are powered off.
  • C. Object resynchronization must be started manually.
  • D. There are too many objects to be synchronized.


Answer : A

Which VMware solution requires vSAN usage?

  • A. VMware Cloud Foundation
  • B. VMware Horizon
  • C. VMware Telco Cloud Automation
  • D. VMware Aria Automation


Answer : A

A vSAN administrator wants to transition from VMware Update Manager to vSphere Lifecycle Manager.
Which element is a mandatory requirement to create an image?

  • A. ESXi Version
  • B. Component
  • C. Firmware and Drivers Add-On
  • D. Vendor Add-On


Answer : A

Page:    1 / 5   
Total 75 questions