Alcatel-Lucent Services Architecture v8.0 (4A0-104)

Page:    1 / 20   
Total 297 questions

Which of the following best describes a VPWS?

  • A. Layer 3 direct Internet access service.
  • B. Layer 2 point-to-point service.
  • C. Layer 2 multipoint-to-multipoint service.
  • D. Layer 3 IP multipoint-to-multipoint VPN service.


Answer : B

Which of the following best describes an IES?

  • A. Layer 3 direct Internet access service.
  • B. Layer 2 point-to-point service.
  • C. Layer 2 multipoint-to-multipoint service.
  • D. Layer 3 IP multipoint-to-multipoint VPN service.


Answer : A

Which of the following are characteristics of a SDP? (Choose 2)

  • A. SDPs are a logical way to direct traffic from one router to another.
  • B. SDPs are a logical way to direct traffic between services.
  • C. SDP IDs are locally unique.
  • D. SDP IDs must be unique across the network.
  • E. SDPs are specific to one service type
  • F. SDPs must use MPLS for their encapsulation


Answer : A,C

The terms "customer" and "service" are used synonymously when describing a service implementation on the Alcatel-Lucent 7750 SR.

  • A. TRUE
  • B. FALSE


Answer : B

Which of the following commands is used to enable an Epipe service?

  • A. config>service# epipe service-id enable
  • B. config>service# vpws service-id enable
  • C. config>service# service-id no shutdown
  • D. config>port# port-id no shutdown
  • E. config>service# epipe service-id no shutdown


Answer : E

Epipe services do no consume any MAC resources because MAC learning is disabled.

  • A. TRUE
  • B. FALSE


Answer : A

When provisioning a spoke-SDP on an Epipe, what MUST match on both ends of the service?

  • A. Service ID
  • B. Customer ID
  • C. SAPID
  • D. VC-ID
  • E. SDPID


Answer : D

Which of the following commands is used to configure a new MPLS SDP?

  • A. configure router sdp sdp-id
  • B. configure service sdp sdp-id create
  • C. configure service mpls sdp sdp-id create
  • D. configure service gre sdp sdp-id create
  • E. configure service sdp sdp-id mpls create


Answer : E

Which of the following commands is used to create a new Epipe service?

  • A. configure epipe service-id customer customer-id create
  • B. configure service epipe service-id customer customer-id create
  • C. configure epipe service-id create
  • D. configure epipe service-id customer customer-id create
  • E. configure epipe service service-id customer customer-id create


Answer : B

When configuring RSVP-TE for transport tunnels, which command enables RSVP by default?

  • A. configure router tunnel
  • B. configure router gre
  • C. configure router rsvp-te
  • D. configure router transport-tunnel
  • E. configure router mpls


Answer : E

Which of the following conditions are necessary in order for service labels to be signaled between two PE routers? (Choose 3)

  • A. LDP must be enabled on both PE routers.
  • B. RSVP must be enabled on both PE routers.
  • C. Traffic engineering must be enabled in the IGP.
  • D. The VC-ID must match between the two PE routers in both directions.
  • E. The transport tunnel must be operationally up between the two PE routers in both directions.
  • F. The SDP ID must match between the two PE routers in both directions.


Answer : A,D,E

A mesh SDP is used to create an Fpipe service.

  • A. TRUE
  • B. FALSE


Answer : B

Which of the following statements are TRUE about configuring a distributed Epipe service?
(Choose 2)

  • A. The vc-id on the spoke-sdp must be explicitly configured.
  • B. The vc-id on the mesh-sdp must be explicitly configured.
  • C. The vc-id on the spoke-sdp can be configured to match the service id.
  • D. The vc-id on the mesh-sdp can be configured to match the service id.
  • E. The vc-id on the spoke-sdp does not have to be explicitly configured and will use the service id.
  • F. The vc-id on the mesh-sdp does not have to be explicitly configured and will use the service id.


Answer : A,C

In a Layer 2 encapsulation, using Martini, what does the first (top) label represent?

  • A. Tunnel Label
  • B. VC Label
  • C. Operational Control Word
  • D. UNI
  • E. NNI


Answer : A

In a Layer 2 encapsulation, using Martini, what does the second (bottom) label represent?

  • A. Tunnel Label
  • B. VC Label
  • C. Operational Control Word
  • D. VPI
  • E. VCI


Answer : B

Page:    1 / 20   
Total 297 questions