Designing Cisco Data Center Infrastructure (DCID) v1.0 (300-610)

Page:    1 / 12   
Total 180 questions

An engineer must use OTV for Layer 2 connectivity between data centers to support virtual machine mobility between the customer sites. To support this requirement, the engineer must ensure the existence of the same default gateway on both sites. Additionally, the operations team reports high bandwidth utilization on site A and wants to optimize the outbound traffic flows to use a local DC exit point.

Which feature must be used to meet these requirements?

  • A. data group
  • B. FHRP filter
  • C. ARP filter
  • D. control group

Answer : D

An engineer is designing a disaster recovery solution. In the event of a node failure, the solution should either direct all of the traffic to another node, or load-balance the traffic across the remaining nodes.

Which solution should be implemented in the design?

  • A. active/active
  • B. cold standby
  • C. active/passive
  • D. warm standby

Answer : A

A company runs mission-critical infrastructure in a single data center. Due to business growth, it plans to open more data centers in the coming years. A network engineer is asked to recommend a network technology for data center interconnection that allows scalability and seamless VM mobility while providing maximum security and fault isolation between data centers.

Which technology must be used to meet these requirements?

  • A. TrustSec
  • B. OTV
  • C. CloudSec
  • D. UDLD

Answer : B

An engineer must design a multitenant solution using Cisco 7709 switches. The solution must support separate routing instances, separate spanning tree domains, and separate firewalls for each tenant.

Which solution meets these requirements?

  • A. vPC
  • B. VDC
  • C. CFS
  • D. VRF

Answer : B

An engineer is designing a Cisco Nexus 7000 Series disaster recovery site using the data center interconnect solution to provide gateway redundancy and needs to ensure that devices use gateways in their own data centers.

Which design approach should be used to accomplish this goal?

  • A. CFS localized to its own data center
  • B. vPC localized to its own data center
  • C. FHRP localized to its own data center
  • D. STP localized to its own data center

Answer : C

Refer to the exhibit.

A cloud service provider deployed three geographically separated Cisco ACI data centers. One of the customers needs to host a clustered application that is spread across the three data centers. The cluster nodes that host the application need a Layer 2 topology to communicate with each other.

Which Cisco ACI topology design meets these requirements?

  • A. Multi-Cloud
  • B. Multi-Site
  • C. Multi-Pod over OSPF EVPN
  • D. Multi-Pod over MP-BGP EVPN

Answer : D

An engineer finishes the initial set up of a VXLAN EVPN network. The engineer is asked to plan for external connectivity that supports redundancy and extends multiple virtual routing and forwarding domains. The requirement is to use the same default gateway addressing across all leaf switches that belong to the VXLAN network.

Which two solutions must be used to meet these requirements? (Choose two.)

  • A. Distributed Anycast Gateway
  • B. VRF-Lite
  • C. Inter-Site Network
  • D. DC Interconnect
  • E. Spanning Tree Protocol

Answer : AD

An engineer must configure an interface for managing and orchestrating a Cisco Nexus device. The interface must be operational if the data and control planes crash, support IPv4 and IPv6 addressing, and have access to its own VRF instance.

Which interface should be used to meet these requirements?

  • A. physical interface
  • B. interface VLAN
  • C. management interface
  • D. loopback interface

Answer : C

An engineer is implementing management access to a Cisco Nexus platform. The customer requires a solution that provides isolation between the data and control planes, in addition to management that uses encryption and authentication. The customer will manage the device using both IPv4 and IPv6.

Which two components should be used to meet these requirements? (Choose two.)

  • A. mgmt0 interface
  • B. SSH protocol
  • C. SNMP
  • D. SVI interface
  • E. Telnet protocol

Answer : BC

An engineer must design a VXLAN EVPN network. The solution should optimize broadcast, unknown unicast, and multicast (BUM) and short BUM replication, and use PIM anycast RP.

Which solution should be included in the design?

  • A. head-end replication
  • B. PIM sparse mode
  • C. PIM dense mode
  • D. ingress replication

Answer : D

A network engineer designs a Cisco Nexus data center network for a client-server farm using a pair of Nexus 9000 Series Switches in a vPC setup. Each server connects with two interfaces to both Nexus switches. The Nexus switches must always initiate the negotiation with the server.

Which feature should be used in this design to ensure traffic is forwarded from the server to the data center network?

  • A. PAgP mode desirable
  • B. LACP mode auto
  • C. LACP mode active
  • D. PAgP mode auto

Answer : C

After experiencing traffic disruptions from the failure of a single router, a customer asks an engineer to design a solution that will prevent this from occurring in the future. While examining the customer's environment, the engineer discovers that the routers are manufactured by a variety of different vendors, and they have varying amounts of CPU and memory resources. Additionally, several of the customer's applications require the ability to fine-tune the load-balancing parameters between multiple gateway routers.

Which solution should be used to meet these requirements?

  • A. VRRP
  • B. FHRP
  • C. HSRP
  • D. GLBP

Answer : A

An engineer must build a VXLAN flood-and-learn network. The customer requires the solution to be based on the IETF documented practice in RFC 7348. The solution must use broadcast, unknown unicast, and multicast (BUM) and include the efficient BUM and short BUM replication modes that use only shared trees.

Which technology meets these requirements?

  • A. MVPN
  • B. PIM sparse mode
  • C. PIM SSM
  • D. Bidirectional PIM

Answer : B

An engineer must secure the payload traversing across the DCI. The solution must support confidentiality and integrity and it must be open standard. The solution must encrypt Ethernet frames regardless of the upper layer protocol used.

Which technology must be used to support these requirements?

  • A. GRE
  • B. OTV
  • C. MACsec
  • D. IPsec

Answer : C

An engineer must interconnect two geographically separated data centers. The service provider offers a Layer 2 Metro Ethernet link. The strict security policy requires that the information that is shared between two sites must be sent encrypted. The application deployed between two sites requires a line-rate throughput regardless of the packet size and speed.

Which solution meets these requirements?

  • A. L2TPv2
  • B. IPsec
  • C. MACsec
  • D. L2TPv3

Answer : C

Page:    1 / 12   
Total 180 questions