VCE Vblock Systems Deployment and Implementation - Core Exam v6.0 (210-010)

Page:    1 / 9   
Total 128 questions

What are three possible results when enabling vSphere High Availability (HA)? (Choose three.)

  • A. Virtual machines will migrate from one host to another as resource availability changes.
  • B. An ESXi host fails and some of the virtual machines restart on other hosts in the cluster.
  • C. A virtual machine fails and automatically restarts on another host in the cluster.
  • D. VMware vSphere Fault Tolerance will be enabled.
  • E. A virtual machine is unable to boot due to limited cluster resources.


Answer : B,C,E

Using PowerPath/VE, which two details are expected outputs from the rpowermt display dev=all command? (Choose two.)

  • A. logical device ID
  • B. serial number for the connected storage array
  • C. initiator ID
  • D. Fibre Channel switch details


Answer : A,B

A host is a member of a high availability (HA) cluster in vCenter. There is a failure of a B- series blade in a Vblock System 720.
What are three ways that vCenter is impacted? (Choose three.)

  • A. vCenter will recognize the host's absence and high availability will restart the virtual machines on the remaining hosts depending on resource constraints.
  • B. The vCenter virtual machine will restart on another available host, there will be no impact to production data on the Vblock.
  • C. vCenter will use Distributed Resource Scheduling (DRS) to vMotion virtual machines based on the reduced resources available.
  • D. The outage will require remediation to restore vCenter functionality.
  • E. The amount of resources available to the cluster will be reduced until the outage is restored.


Answer : A,C,E

What are three purposes of the master host in a vSphere high availability (HA) cluster?
(Choose three.)

  • A. to monitor the state of slave hosts
  • B. to monitor the power state of all protected virtual machines
  • C. to manage the lists of cluster hosts
  • D. to migrate virtual machines when a vMotion is requested
  • E. to install the HA agent on newly added hosts


Answer : A,B,C

You observe that a host in a high availability (HA) cluster shows as disconnected within vCenter. The virtual machines running on the disconnected host have not automatically restarted as expected.
What is the cause of this problem?

  • A. NTP was not configured on the HA cluster.
  • B. vMotion is not enabled on the cluster hosts.
  • C. The disconnected host was the master host.
  • D. The host is still exchanging a data store heartbeat.


Answer : D

A host has been placed into maintenance mode in a Distributed Resource Scheduler
(DRS) enabled cluster for patching. The virtual machines have not migrated as expected.
DRS settings have been verified as fully automated at the cluster level.
What would cause this condition?

  • A. The selected host is using a different ESXi version than the rest of the cluster.
  • B. vMotion is not enabled on the vMotion vmkernel interface for the selected host.
  • C. The high availability agent has not been properly installed on the selected host.
  • D. DNS is not enabled at the host level for the selected host.


Answer : B

Which two statements are correct regarding VCE implementation of a persistent scratch partition? (Choose two.)

  • A. You must configure a persistent scratch partition on the boot-from-SAN VMFS data store.
  • B. You must configure a persistent scratch partition on the boot-from-SAN NFS data store.
  • C. Vblock Systems use centralized monitoring with syslog and SNMP in place of a persistent scratch location.
  • D. VCE uses the persistent scratch partition to ensure that critical log files are available.


Answer : A,D

On a Vblock System 720, what is the VCE supported tool used to manage a storage array?

  • A. Unisphere for VMAX
  • B. Ionix ControlCenter
  • C. Symmetrix System Viewer
  • D. Symmetrix Management Console


Answer : A

In a Vblock System 720, what is the maximum standard LUN size on an EMC Symmetrix
VMAX 10K/20K/40K?

  • A. 20 GB
  • B. 64 GB
  • C. 240 GB
  • D. 2,457 GB


Answer : C

A storage administrator needs to access a Vblock System 200 storage array using EMC
Unisphere GUI.
What information must the administrator obtain to log in?

  • A. the IP addresses of the two storage processors
  • B. the IP address of the service processor
  • C. the IP address of the data mover
  • D. the IP address of the x-blade


Answer : A

What is the purpose of the EMC VNXe Connection Utility installed on the Vblock System
320 array management server?

  • A. to perform upgrades
  • B. to configure the management IP address
  • C. to provision storage
  • D. to troubleshoot performance issues


Answer : B

You are installing a Vblock System 720 and notice that no Cisco UCS B230 blades are logging into the Cisco MDS 9148 switches.
Which feature must be enabled on the Cisco MDS 9148 to resolve the issue?

  • A. NPIV
  • B. TACACS+
  • C. RADIUS
  • D. NPV


Answer : A

In the Vblock System 720, what describes the VCE standard method of zoning?

  • A. multi initiator to single target
  • B. single initiator to multi target
  • C. single initiator to single target
  • D. multi initiator to multi target


Answer : C

You are assigned to deploy a new host in a Vblock System, with block storage attached.
Which type of zoning would be performed on the Cisco 9148 switch to accomplish this task?

  • A. port zoning
  • B. WWPN zoning
  • C. symbolic node name zoning
  • D. WWNN zoning


Answer : B

You have just deployed a new ESXi host in a Vblock System 320 and only have TCP/IP available for storage access.
Which protocol would be used for data store access?

  • A. NFS
  • B. CIFS
  • C. iSCSI
  • D. FCP


Answer : A

Page:    1 / 9   
Total 128 questions