Netapp NS0-509 - NetApp Certified Implementation Engineer\xe2\x80\x94SAN Specialist Exam
Page: 2 / 12
Total 59 questions
Question #6 (Topic: Topic 1)
A company has 20 ESX hosts. Ten of the hosts are connected using FC, and the rest are connected over iSCSI. The FC host HBA queue depth is set to 32, and
the iSCSI LUN queue depth is set to 64. The FC hosts are now experiencing random connectivity issues.
In this scenario, what would be the reason for the disconnects?
the iSCSI LUN queue depth is set to 64. The FC hosts are now experiencing random connectivity issues.
In this scenario, what would be the reason for the disconnects?
A. The FC host has a lower queue depth.
B. According to the IMT, unsupported HBA firmware is in use.
C. All of the hosts are part of the same cluster.
D. The queue depth is not consistent across the cluster.
Answer: A
Question #7 (Topic: Topic 1)
You want to ensure maximum performance of iSCSI LUNs on an AFF A220.
In this scenario, which two actions will accomplish this task? (Choose two.)
In this scenario, which two actions will accomplish this task? (Choose two.)
A. Disable flow control.
B. Configure virtual LAN (VLAN).
C. Enable flow control.
D. Enable jumbo frames.
Answer: CD
Question #8 (Topic: Topic 1)
You are provisioning storage to an ESX host that uses iSCSI.
According to NetApp best practice, which three actions accomplish this task? (Choose three.)
According to NetApp best practice, which three actions accomplish this task? (Choose three.)
A. Enable the iSCSI service.
B. Bind the iSCSI ports to the software iSCSI adapter.
C. Install Virtual Storage Console (VSC) for VMware.
D. Enable BGP on the switch.
E. Configure MTU 1500 on the switch.
Answer: BCE
Question #9 (Topic: Topic 1)
Click the Exhibit button.
[Network-NS0-509-1.0/xmlfile-7_1.png]
A customer has an AFF A700 connected to a Cisco switch and has verified connectivity but cannot see any LUNs. The customer issued the run -node
scaling-01 -command fcp topology show command to verify the connection.
Referring to the exhibit, what needs to be enabled on the Cisco switch?
[Network-NS0-509-1.0/xmlfile-7_1.png]
A customer has an AFF A700 connected to a Cisco switch and has verified connectivity but cannot see any LUNs. The customer issued the run -node
scaling-01 -command fcp topology show command to verify the connection.
Referring to the exhibit, what needs to be enabled on the Cisco switch?
A. Trunking needs to be enabled.
B. VSAN needs to be enabled.
C. NPIV needs to be enabled.
D. VFC needs to be enabled.
Answer: D
Question #10 (Topic: Topic 1)
Click the Exhibit button.
[Network-NS0-509-1.0/xmlfile-8_1.jpg]
A customer is using both FC and NVMe in a cluster. The customer needs to do some work on AFF_1.
Referring to the exhibit, what will happen?
[Network-NS0-509-1.0/xmlfile-8_1.jpg]
A customer is using both FC and NVMe in a cluster. The customer needs to do some work on AFF_1.
Referring to the exhibit, what will happen?
A. The NVMe namespaces on AFF_2 will be available after takeover of AFF_1.
B. The FC LUNs that use cluster interconnect to access the LUNs on AFF_1 will be unavailable after failover.
C. The FC LUNs on node AFF_2 will be unavailable after failover of AFF_1.
D. The NVMe namespaces on AFF_1 will be unavailable after takeover by AFF_2.
Answer: C
