Microsoft 70-680 - TS: Windows 7, Configuring Exam
Page: 1 / 113
Total 564 questions
Question #1 (Topic: Topic 1)
You are configuring static IPv4 addresses for two computers, Perth and Brisbane, on an
isolated private wired subnet. You configure Perth with the IPv4 address 172.16.10. 140
and the subnet mask 255.255.255.0. You configure Brisbane with the IPv4 address
172.16.10. 210 and the subnet mask 255.255.255.0. You enter ping 172.16.10.140 on
Brisbane, but the command times out. Similarly, entering ping 172.16.10.210 on Perth fails
to locate the Brisbane computer's IPv4 address. What is the likely reason for this lack of
connectivity?
isolated private wired subnet. You configure Perth with the IPv4 address 172.16.10. 140
and the subnet mask 255.255.255.0. You configure Brisbane with the IPv4 address
172.16.10. 210 and the subnet mask 255.255.255.0. You enter ping 172.16.10.140 on
Brisbane, but the command times out. Similarly, entering ping 172.16.10.210 on Perth fails
to locate the Brisbane computer's IPv4 address. What is the likely reason for this lack of
connectivity?
A. DNS service is not available on the subnet.
B. The computers should have different subnet masks.
C. You have not specified a default gateway.
D. You need to permit ICMPv4 traffic through the firewalls of both computers.
Answer: D
Question #2 (Topic: Topic 1)
You have a computer that runs Windows 7.
You update the driver for the computer's video card and the computer becomes
unresponsive.
You need recover the computer in the minimum amount of time.
What should you do?
You update the driver for the computer's video card and the computer becomes
unresponsive.
You need recover the computer in the minimum amount of time.
What should you do?
A. Restart in safe mode and then roll back the video card driver.
B. Restart in safe mode and then revert the computer to a previous restore point.
C. Start the computer from the Windows 7 installation media. Select Repair your computer and then select System Restore.
D. Start the computer from the Windows 7 installation media. Select Repair your computer and then select System Image Recovery.
Answer: A
Question #3 (Topic: Topic 1)
You plan to deploy Windows 7 to 100 computers on your corporate network.
You install Windows 7 on a computer.
You and need to prepare the computer to be imaged.
What should you do before you create the image of the computer?
You install Windows 7 on a computer.
You and need to prepare the computer to be imaged.
What should you do before you create the image of the computer?
A. At the command prompt, run the Dism command.
B. At the command prompt, run the Sysprep command.
C. Start the computer from the Windows Preinstallation Environment (Windows PE) and then run the Imagex command.
D. Start the computer from the Windows Preinstallation Environment (Windows PE) and then run the Wpeutil command.
Answer: B
Question #4 (Topic: Topic 1)
You have a Virtual Hard Disk (VHD) and a computer that runs Windows 7. The VHD has
Windows 7 installed.
You need to start the computer from the VHD.
What should you do?
Windows 7 installed.
You need to start the computer from the VHD.
What should you do?
A. From Diskpart.exe, run Select vdisk.
B. From Disk Management, modify the active partition.
C. Run Bootcfg.exe and specify the /default parameter.
D. Run Bcdedit.exe and modify the Windows Boot Manager settings.
Answer: D
Question #5 (Topic: Topic 1)
You have two computers named Computer1 and Computer2 that run Windows 7.
You need to ensure that you can remotely execute commands on Computer2 from
Computer1.
What should you do?
You need to ensure that you can remotely execute commands on Computer2 from
Computer1.
What should you do?
A. Run Winrm quickconfig on Computer1
B. Run Winrm quickconfig on Computer2
C. Enable Windows Remote Management (WinRM) through Windows Firewall on Computer1
D. Enable Windows Remote Management (WinRM) through Windows Firewall on Computer2
Answer: B
